Every homeowner has an amazing opportunity to realize their design ideas for improving their living space. And this is not only the bedroom, living room, kitchen and hallway. The bathroom is the place where you can safely use your imagination, thereby increasing the functionality and comfort of the room.
If improvisation is difficult, then the Internet offers a huge selection of photos of the bathroom in the house. So there are practically no restrictions, which cannot be said about those who live in standard apartments.
However, arranging a bathroom in a private home is not as simple as it might seem at first glance. Although, the use of modern technologies and materials can solve any, even quite difficult, problems.
The result of all this is to get a beautiful room that will be as comfortable and aesthetically pleasing as a bedroom or living room.
Cost of water supply for a private house
Water supply from a well
Water supply from a well
What's included
- Installation of a pump for source depths up to 20 m/linear
- Installation of a pipeline from the source to the house
- Installation of a hot water boiler
- Installation of water pre-treatment unit
- Pump automation control device
- Installation of water supply pipes for one sanitary unit
- Electrical installation kit for water supply system
Not included
- Plumbing installation:
- Shower cabin
- Toilet
- Sink
- And other hygiene products
- Excavation work, either on your own or for an additional fee
- Cause:
- You need to know the product range
Rates by month
| January from 27,000 ₽ | February from 29,000 ₽ | March from 32,000 ₽ |
| April from 35,000 ₽ | May from 37,000 ₽ | June from 39,000 ₽ |
| July from 41,000 ₽ | August from 43,000 ₽ | September from 45,000 ₽ |
| October from 47,000 ₽ | November from 45,000 ₽ | December from 55,000 ₽ |
Water supply at home
In the case where it is impossible to connect a centralized water supply system in a private house, it would be advisable to decide on an autonomous line. Despite the complexity of the task, the result is an independent communication node with adjustable parameters, consisting of two main systems : water production and distribution.
To implement the first stage, you will need to choose a method for obtaining drinking water. The selection of the type of water intake structure largely depends on the characteristics of the geological situation of the area, the depth of the aquifers and the amount of water used.
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
Home water supply
Autonomous water supply
Autonomous water supply – equipment sales
Water supply at home
The question of having their own source of water supply arises for every family planning to build a country house remote from centralized communications. The solution to the problem is to select the appropriate method: digging a well or drilling a well .
Objective reasoning when comparing these structures is very incorrect, because even a standard well “on sand” will have significantly more technological advantages compared to the most modern well . In addition, the arrangement of the well is carried out exclusively taking into account the location of the septic tank. The regulations state that there must be a distance of at least 200 m between the two systems, which is problematic in areas with a small territory. In this matter, a well is more practical - it can be created almost anywhere, since the network of deep artesian waters is quite extensive.
The fact of comparing cost and quality is also important. In the case of digging a well to a standard installation depth of 10 rings, the estimate for the work will be much cheaper than for a well. However, there is no need to talk about high water quality here. This aspect is due to the low filtration of water resources. This is especially noticeable in the spring, when snow melts, which causes the turbidity of the composition. It is also worth considering seasonality, fluctuations in water levels are possible, and drying out is possible in the summer.
Materials for water supply to a house from a well or borehole
| A pump that supplies water to the house from a source. |
| Pipeline from the pump connecting to the main line pipe going into the trenches to the house (consumer) |
| Water supply system drainage unit . There are two options: a tee with a ball valve (economical, when using it you will need to be able to get to it, and it is located at the depth to which the main water supply line to the house is routed, namely at a depth of about 1.5 m); motorized ball valve (this is a valve with an electric drive that can be controlled from home, namely open or close using an electric switch) |
| A protective element for the passage of a pipe through a concrete well . The pipeline tends to constantly rub, namely to expand due to temperature differences. Accordingly, to prevent the pipe from “rubbing” against the walls of the concrete ring, a special element is installed to protect the pipeline from “chafing.” |
| Electric power cable. A cable to provide electrical energy to the water supply pump itself, which goes from the house where the pressure switch (pump control) is installed to the pump. |
| Water supply line from the well to the house . The main supply pipeline is located in the ground, which provides the water supply system to the consumer. |
| Heating cable. |
| Wash filter. |
| Thread filter. |
| Automatic pump protection. |
| Pump pressure switch. |
| Hydraulic accumulator. |
| DHW boiler. |
| Pipeline for distribution to consumer points. |
| Plugs and shut-off valves. |
| For an accurate calculation, an engineer will be required to inspect the work site. |
Materials for home water supply
Main stages
- Preparatory work.
- Design development (drawing up a project, calculations, selection of building materials).
- Providing the premises with communications (electricity, water, ventilation, sewerage).
- Protecting surfaces from penetration of moisture, microorganisms, temperature changes, the formation of mold stains and fungi.
- Finishing surfaces with previously selected materials.
- Arrangement of the bathroom inside, creation of comfort (connection of plumbing, furniture, installation of technical elements and designer accessories).
Cost of water supply for a private house
Water supply from a well
Water supply from a well
What's included
- Installation of a pump for source depths up to 20 m/linear
- Installation of a pipeline from the source to the house
- Installation of a hot water boiler
- Installation of water pre-treatment unit
- Pump automation control device
- Installation of water supply pipes for one sanitary unit
- Electrical installation kit for water supply system
Not included
- Plumbing installation:
- Shower cabin
- Toilet
- Sink
- And other hygiene products
- Excavation work, either on your own or for an additional fee
- Cause:
- You need to know the product range
Rates by month
| January from 27,000 ₽ | February from 29,000 ₽ | March from 32,000 ₽ |
| April from 35,000 ₽ | May from 37,000 ₽ | June from 39,000 ₽ |
| July from 41,000 ₽ | August from 43,000 ₽ | September from 45,000 ₽ |
| October from 47,000 ₽ | November from 45,000 ₽ | December from 55,000 ₽ |
Water supply at home
In the case where it is impossible to connect a centralized water supply system in a private house, it would be advisable to decide on an autonomous line. Despite the complexity of the task, the result is an independent communication node with adjustable parameters, consisting of two main systems : water production and distribution.
To implement the first stage, you will need to choose a method for obtaining drinking water. The selection of the type of water intake structure largely depends on the characteristics of the geological situation of the area, the depth of the aquifers and the amount of water used.
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
Home water supply
- Autonomous water supply
- Autonomous water supply – equipment sales
Water supply at home
The question of having their own source of water supply arises for every family planning to build a country house remote from centralized communications. The solution to the problem is to select the appropriate method: digging a well or drilling a well .
Objective reasoning when comparing these structures is very incorrect, because even a standard well “on sand” will have significantly more technological advantages compared to the most modern well . In addition, the arrangement of the well is carried out exclusively taking into account the location of the septic tank. The regulations state that there must be a distance of at least 200 m between the two systems, which is problematic in areas with a small territory. In this matter, a well is more practical - it can be created almost anywhere, since the network of deep artesian waters is quite extensive.
The fact of comparing cost and quality is also important. In the case of digging a well to a standard installation depth of 10 rings, the estimate for the work will be much cheaper than for a well. However, there is no need to talk about high water quality here. This aspect is due to the low filtration of water resources. This is especially noticeable in the spring, when snow melts, which causes the turbidity of the composition. It is also worth considering seasonality, fluctuations in water levels are possible, and drying out is possible in the summer.
Materials for water supply to a house from a well or borehole
| A pump that supplies water to the house from a source. |
| Pipeline from the pump connecting to the main line pipe going into the trenches to the house (consumer) |
| Water supply system drainage unit . There are two options: a tee with a ball valve (economical, when using it you will need to be able to get to it, and it is located at the depth to which the main water supply line to the house is routed, namely at a depth of about 1.5 m); motorized ball valve (this is a valve with an electric drive that can be controlled from home, namely open or close using an electric switch) |
| A protective element for the passage of a pipe through a concrete well . The pipeline tends to constantly rub, namely to expand due to temperature differences. Accordingly, to prevent the pipe from “rubbing” against the walls of the concrete ring, a special element is installed to protect the pipeline from “chafing.” |
| Electric power cable. A cable to provide electrical energy to the water supply pump itself, which goes from the house where the pressure switch (pump control) is installed to the pump. |
| Water supply line from the well to the house . The main supply pipeline is located in the ground, which provides the water supply system to the consumer. |
| Heating cable. |
| Wash filter. |
| Thread filter. |
| Automatic pump protection. |
| Pump pressure switch. |
| Hydraulic accumulator. |
| DHW boiler. |
| Pipeline for distribution to consumer points. |
| Plugs and shut-off valves. |
| For an accurate calculation, an engineer will be required to inspect the work site. |
Materials for home water supply
Pipe selection
In work that involves installing communications into suburban buildings, the most difficult thing is to make holes in the floor or walls. Other procedures, such as cutting and joining pipes, are quite simple. In addition, you will need to connect the pipeline to the collector, install pumping equipment and filtration systems. This explains why even a beginner can build a water supply system with his own hands.
First you need to figure out what materials are best to buy pipes from:
- Copper pipes have the highest price. They are resistant to rust and ultraviolet radiation. In addition, microorganisms cannot encroach on copper pipes, and such products are not afraid of high pressure. There are no significant changes in such products in the event of temperature changes. In addition, copper pipes are capable of excellent heat transfer. The only disadvantage of copper products is their high price.
- Metal-plastic pipes. These products are aluminum pipes that are protected outside and inside with polyethylene. Thanks to its smooth surface, deposits do not accumulate in the pipes and rust does not form. The outer layer of the pipes reliably protects them from condensation and ultraviolet rays. Such pipes also have several disadvantages - they are sensitive to high temperatures and can become deformed when heated to 95 degrees. In addition, metal-plastic pipes are sensitive to freezing of the coolant.
- Steel pipes. This version of the product is old and proven. Such products serve for a long time and are not afraid of mechanical stress. However, they are not affected by rust. In addition, pipes must be threaded for installation. They can be soldered, but this process is quite labor-intensive.
- Polypropylene pipes.
Today they are most popular when installing a water supply system in a country house. This is due to their high performance characteristics. In addition, they are not subject to oxidation and are durable. They are easy to install and connections do not need to be checked, making it easy to hide pipes under the finishing surface. However, to connect the elements you must have an electric welding machine. Important! If polypropylene products are chosen as the material, you should pay attention to the need to use reinforced pipes when carrying hot water.
The price of installing a plumbing system depends not only on the number of pipes, but also on the material they are made of. Therefore, when purchasing, you should focus on the price/quality ratio.
Choosing the optimal pipe diameter is as important as selecting the material. This is due to the characteristics of the passage of water in the water supply system. For example, if the pipes have a too small diameter, flow turbulence may occur. In this case, the water will move through the pipes with noise, and lime deposits will accumulate inside them.
The diameter of the pipes depends on the total length of the pipeline:
- If the pipeline will have a total length of less than 30 m, it is better to choose a diameter of 25 mm.
- If the length of the water pipe exceeds 30 m, you should purchase pipes with a diameter of 32 mm.
- In the case of short pipelines less than 10 m long, it is worth choosing products with a diameter of 20 mm.
To properly arrange a water supply system in a wooden country house, you should select the optimal diameter of the collector pipe. This is necessary so that it provides ample opportunities for the use of water by several consumers. There are several standard calculations by which the diameter of pipes is determined:
- With a pipe diameter of 25 mm, the product can flow about 30 l/min.
- In the case of a diameter of 32 mm, the pipe can flow 50 l/min.
- If the pipe diameter is 38 mm, 75 l/min will pass through it.
When a large family lives in a house and there are many water intake points in the house, situations often occur when they are used simultaneously. If you add up the volumes of water consumed by several appliances, you can get a pretty impressive number.
When the water supply is installed for a small family, and there are quite a lot of water consumers in the house, the calculation is performed according to a different rule. It is necessary to calculate how much water is consumed at several water intake points and reduce this figure by 25-40%. This figure will be an approximate family expense.
Water supply to a dacha from a well
Using a well as a source of water , you save your family budget by choosing the most durable option. The service life of the well is more than 50 years. It requires repairs less often and is more convenient to use; in the event of a power outage, it is possible to draw water from the well with a bucket. To organize a water supply, you will need to dig a well , a powerful pump and pipes (hoses); in addition, you can install filters for drinking water. There are many recommendations and ways to determine the ideal location of a well.
Water supply to a dacha from a well
It depends on nearby buildings and underground water sources. If there is a well , it is enough to restore it, strengthen the walls and carry out cleaning work. The pumping station is installed in the dacha (in a separate room) or a specially built small room is built. Next, hoses are connected to the pump and water is supplied to the country house or closer to the garden. Water supply from a well is simple, convenient and economical.
- Installation of water filters
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
- Water supply well
Water supply to a dacha from a well
The well is considered one of the most accessible and common sources of water for private homes . This method is preferred if the water is at a depth of 5-15 meters. Depth and productivity are the main criteria when constructing a well .
House water supply + well
One of the advantages of supplying water to a private home using a well is that in the absence of electricity, water can be extracted from it manually using a rope and a bucket. In addition, the price for digging a well is much less than for installing a well, especially an artesian one. Water supply at home.
Autonomous water supply
Bathroom interior design options
Today, they try to make the floor in the bathroom with natural textures. The hit of interiors is the use of porcelain stoneware in bright or soothing colors.
A great bathroom interior is basically a fashionable, beautiful palette. The dominant colors of a modern bathroom are white, turquoise, gray in light colors, and green closer to a mint shade.
On a note! For an additional source of heat in the bathroom, it is recommended to install a heated floor. The system is so simple that it is quite possible to handle the installation yourself.
