Screw or dowel for concrete: its types and how to use it. dowel screw for concrete

How to screw a self-tapping screw into a brick. How to screw a self-tapping screw into a brick wall

First things first, first things tools

nails, screws, rivets, anchors
Reliable fastening of the structure is a guarantee that it will last a long time without requiring additional repairs

In this regard, it is very important to choose reliable tools and fastening elements. And this choice must be approached with full responsibility.

You will need special tools. An impact drill is best.

You can also choose a regular drill, to which a pobedit tip is selected. But in this case the work will be more complicated. In terms of cost, this will result in approximately the following figures: from 800 rubles for the tool itself and from 40 to 50 rubles in addition for the drill. Running sizes are considered to be 6 and 8 mm diameters.

The list of materials that such tools can work with is extensive. Their choice will depend on the future load of the suspended structure. The most popular are the following:

• self-tapping screws for bricks;
• dowels (will help withstand heavy loads);
• anchors (capable of holding very heavy things);
• rivets (for delicate glass shelves);
• corners (for small cabinets and shelves);
• regular nails combined with all the others.

It is also important to consider what kind of product is used for laying the surface - it can be either solid or hollow. The types and grades of this product will also tell you how reliable the screws used for bricks are

Main rules of fastening

correct fastening of screws

Before starting work, you need to understand some rules. They will help not to spoil the surface and carry out the correct fasteners:

1. The most basic requirement that must be met when attaching something to a wall made of such material is not to spoil the mortar that holds the blocks together.
2. It would be best to use a drill. It will help to avoid cracks that may appear if, for example, you try to “drive” self-tapping screws into a brick with a hammer drill.
3. Drilling should be unhurried and gradual. This approach will help to secure any element to such a wall.

Working methods

working with self-tapping screws

There are several ways to make it easier to place fasteners on such a wall. Some of them are quite interesting:

If we are working with dowel nails, it is important to prepare a container with water - in it we will periodically cool the drill. You can wrap electrical tape around the drill itself, which will serve as a limiter.

After the hole is ready, insert the dowel glass and hammer in the nail. In order to facilitate the process that self-tapping screws go through when driven into a brick, you can use the “old” method. The dowel inserted into the drilled hole is strengthened with a wooden peg. Another “old-fashioned” method would be to drill a hole and screw a plug or cap into it, previously soaked in PVA glue. Then the “excess” peeking out from the wall is cut off and a self-tapping screw is screwed in. But such fastening is considered short-lived. It is best to use dowels designed specifically for brick walls. They have projections that will not allow it to turn, even if a screw or nail is screwed in. This rule applies even to hollow bricks, in which they will roll up into a knot and occupy the entire required volume. When you need to decorate an external wall (for example, the entrance of a house), you can use corners along with dowels and screws. They will not only connect the structure and the wall, but will even become supporting elements.

How to screw it in?

In order for the self-tapping screw to be sufficiently firmly screwed into the concrete and ensure a strong fixation of the entire structure, you first need to check the material itself. If the concrete is “loose” and crumbles a little, then you should first make a small depression at the point where the device will be inserted.

The hole for the screw can be made using a Phillips screwdriver. If you don’t have it, take an awl, but it’s better not to use a drill. The recess made will not allow the element to move to the side during installation. It will be fixed strictly perpendicular to the surface.

During the screwing process, the self-tapping screw will begin to delaminate the material. When installing fasteners, it is necessary to take into account some rules. Remember that the length of the clamp should be significantly less than the thickness of the concrete. Otherwise, the tip of the fastener will simply end up on the outside of the other side.

Depending on the density of the concrete base, the distance between individual screws without drilling should be from 12 to 15 centimeters. If you are fastening the edges of concrete products, then you should leave a small distance from it. It should be twice the length of the latch itself.

The following video shows how to drive a screw into concrete.

Location requirements

There are requirements for the location of hardware, for example, markings are necessary in order to screw in the necessary fasteners efficiently and at the required distance. There are the following rules for placing screws:

• from the edge of the product that is attached, it is necessary to retreat a distance equal to twice the length of this fastener;
• the hole in the wall should be slightly larger than the screw;
• the minimum dowel fit for light material is 6 cm, heavy material is 4 cm;
• the distance between the screws is from 12 to 15 cm, depending on the density of the concrete;
• The diameter of the hole is equal to the cross-sectional diameter of the self-tapping screw together with the dowel.

How to use?

There are two ways to screw a dowel into a concrete wall - either with or without a dowel. The presence of a plastic sleeve in the hole will provide a more reliable grip thanks to its “shoots” that work as spacers. The use of a dowel is required in cases where there is an excessive load on the screw or the part needs to be secured to porous or cellular concrete. In principle, a plastic spacer should also be used when working on structures that are subject to vibration. Installing a self-tapping screw for concrete with a dowel begins with the fact that it is necessary to drill a recess in the wall, the diameter of which will coincide with the cross-section of the sleeve, and the depth will be 3-5 millimeters greater. You can drill with an electric drill, but when processing soft or porous materials it is better to use a screwdriver with a drill.

The hammer drill is used in situations where the density of the concrete wall is 700 kilograms per cubic meter or even more. The resulting hole is cleared of debris, and then the dowel is driven into the socket with an ordinary hammer. It will be correct to screw the self-tapping screw itself with a simple screwdriver or a screwdriver with a bat into an already prepared place. Installation of dowels on concrete can occur without preliminary drilling. This is done either according to a template or with preliminary application of a channel outline. When using a template, you will need to screw the hardware into the concrete surface directly through the hole of the pattern made from a piece of wood or a fragment of a board. If everything is done correctly, the fastener will be securely fastened perpendicular to the surface.

When working with basting, the hole will need to be drilled slightly smaller than the diameter of the screw itself. A dowel with a herringbone thread is usually driven into concrete with a hammer. It should definitely be mentioned that the use of screws requires preliminary marking. The distance from the edge of the structure must be equal to at least twice the length of the anchor

In addition, it is important that the depth of the hole exceeds the length of the screw by an amount equal to its diameter. When working with lightweight concrete, you should select a planting depth of 60 millimeters, and for heavy blocks - about 40 millimeters

When a dowel is selected for fixing wooden structures or window frames on concrete or brick walls, the surface is first cleaned and a recess is drilled with a drill. Further, approximately 5-6 centimeters retreat from the edge. When installing PVC window frames, the gap between the screws is maintained at 60 centimeters. In the case when we are talking about wooden or aluminum structures, you will need to maintain a distance of 70 centimeters, and plus maintain 10 centimeters from the corner of the frame to the racks.

Some experts recommend soaking the drill in water or oil during the work process to avoid excessive heat. If the dowel will be screwed in with a screwdriver, it should be selected in accordance with the drawings printed on the head of the product. Both curly and cross-shaped varieties can be suitable

To remove a broken screw from a concrete wall, it is better to drill the area around it and carefully pick up the fasteners with thin round nose pliers. Next, the resulting hole is closed with a plug of the same diameter, coated with PVA glue, or filled with a larger dowel

To screw the baseboards with self-tapping screws on concrete, manipulations will need to start from the inner corner of the room.

Having made the markings, you need to prepare holes for screws in the baseboard and on the wall. First, the dowels are attached, and then the plinth is carefully fixed to the wall using self-tapping screws. In the case when the surface is made of concrete, a recess equal to 4.5 centimeters is usually drilled, and the fasteners themselves are carried out at a distance of 3 centimeters. When working with a wall made of sand-lime brick, the hole will need to be deepened by 5.5 centimeters, and anchoring will be carried out to a depth of 4 centimeters. This type of self-tapping screws can also be used for pumice surfaces - in this case, you will first need to create a recess equal to 6.5 centimeters, and keep the gap between the hardware equal to 5 centimeters.

To learn how to drive a screw into concrete, watch the following video.

How to drill through concrete with a self-tapping screw?

There are two reliable ways to screw a self-tapping screw into concrete - with or without a dowel. Dowels are used in cases where strong fixation cannot be ensured without additional adhesion. The use of dowels is appropriate in the following situations:

• the self-tapping screw may not withstand heavy loads, which is why additional fixation is needed;
• when working with porous, heterogeneous concrete bases;
• screwing into concrete that is subject to vibration.

To install self-tapping screws, follow the following sequence:

1. Using a special tool (drill, screwdriver with drill), we make a hole with a diameter similar to that of a dowel and 5 mm longer than it.
2. We clean the hole from any remaining metal shavings and dirt.
3. Drive the dowel tightly into the hole using a hammer.
4. We tighten the self-tapping screw.

If you decide that the self-tapping screw can be tightened without pre-drilling, the operation algorithm will be as follows:

• drill a hole with a smaller diameter. We take the herringbone hardware and push it into the prepared hole with a hammer;
• if you plan to work according to a pre-prepared template, the self-tapping screw will need to be screwed through the hole on the template. You can make the template yourself from a wooden block. We install the pattern perpendicular to the surface and begin work.

Dowel selection

When purchasing various objects to attach to a concrete wall, you should choose the right dowel for concrete; its approximate dimensions can be selected from the table:

Table for determining the dimensions of a fastener depending on the type of load on it

Fasteners are selected depending on the type of place where they will be used.

Before driving a dowel into a concrete wall, the future load must be taken into account:

To secure structures of large mass, for example, wall bars or wall-mounted exercise machines, it is best to use dowels with a mounting depth of at least 85 mm; When fixing horizontally into a concrete wall, it is recommended to purchase fastening elements in which the fastening depth is at least 30 mm, and the diameter of the dowel on the outside is 7 - 11 mm; For the installation of a suspended ceiling, lamps, where the main load is located below, fasteners should be selected with spacer antennae and transverse notches; When selecting dowels for an already drilled hole, it is important that the parameters of the fastener and the diameter of the hole match each other. In this case, the dowel for expanded clay concrete or other material must have a diameter no less than the size of the hole; When using mounting fasteners, in order to prevent the destruction of weak walls, the dowel should serve as a softening pad

In this case, the fastener fits quite tightly to the fastener, and the load is distributed evenly throughout the product.

Features of installing dowels in the wall

Technology for installing dowels in a concrete wall

To do the work yourself you need to purchase:

• Electric drill;
• Pobedit drill;
• Sharp nail;
• Dowel of the desired design;
• Electrical tape;
• Small hammer.

After preparing all the tools, you can begin installing the dowels.

Work instructions:

• Mark the installation location of the fasteners with a ballpoint pen or a simple pencil;
• A small indentation is made with a nail, hacksaw or pin. This will allow you to correctly align the drill when making a hole;

• If the number of dowels was calculated incorrectly, you can make the product yourself. To do this, take wooden blocks of the required length. They are given a rounded cross-section, thickening at the top and decreasing in diameter at the bottom. After this, screw the screws into the concrete without a dowel;
• A drill of the required diameter is inserted into an electric drill;

• The drill is placed in the previously made recess. The drill is positioned strictly perpendicular to the surface;
• The resulting dust and cement chips are removed from the drilled hole. This can be done using a vacuum cleaner;
• The dowel is carefully inserted and hammered in with a hammer, but not too hard, until it stops;
• A screw is screwed into the dowel if it is included in the structure.

To correctly hammer a dowel into a wall, you should watch the video in this article.

Installing a spring dowel

Self-tapping screws for concrete: wall hardness is not a problem!

They also differ in terms of use. Galvanized models can be used indoors as well as outdoors. Copper dowel does not like external influences, and therefore there is no reason to install it outside. Blackened mestizo is protected in the worst way of all, and therefore it is better to use it in places where moisture will not get in. Dowels have several important parameters that you need to know when using:.

It is necessary to know the depth of anchoring, as well as drilling of various walls.

It depends on the material that was used in the construction of the structure: Dowels are very often used when installing wooden structures, PVC windows, aluminum profiles, wooden frames to concrete structures, brick or other walls.

Before you start screwing in the screw, you need to drill a hole in the brick using a special drill. After the marking has been made, you need to start screwing in the dowel. It must be secured very carefully.

Based on the color of the coating, screws are divided into three categories:. A characteristic feature of all types is strength. The head is flat and easily hidden in the design.

Benefits of use

The main difference between the dowel and other fasteners is the thread. The screws are cut along the entire length and unevenly, which creates exceptional strength during fastening. The properties of the thread allow us to divide products into three groups:

This is convenient: it significantly speeds up and simplifies any finishing task. Although experienced builders advise not to be lazy with preparing the hole.

When choosing screws for concrete, you need to take into account not only the technical characteristics of the product, but also the characteristics of concrete products, including weight. Pins are used for fastening wooden and aluminum structures to a concrete brick base. Using screws is convenient and easy.

Driving a screw into a concrete wall is not an easy task. Every man had to do this at some point. After all, everyone has gone through renovations in their homes. Installing a screw will not cause any difficulties if you know the fastening technology in advance and have an idea of ​​the types and features of this fastening material.

If there is a dowel in a pre-drilled hole, the dowel can withstand a large load. If there is no load on the fastening material, you can do without a dowel.

What is a concrete dowel?

The folk method will help prevent loosening in the second case. Place pieces of matches into the hole made. They will seal the position of the fastener and prevent it from loosening. Applying dowels is a simple procedure. Before starting work, prepare the following tools:. Pre-mark future holes. Each type of work has its own. A distance from the edge of cm is maintained, the distance between points is a maximum of 60 cm.

After marking the points, you can start drilling holes. In appearance, the anchor self-tapping screw for concrete is practically no different from simple screws. But there are some special characteristics that products suitable for DIY installation in concrete surfaces must have. Can I drill into a concrete wall with a screwdriver or electric drill?

In fact, you shouldn't ruin your instrument. Find a hammer drill and don’t worry, but in extreme cases, choose the right drill, taking into account the following criteria: Using such fasteners is quite convenient and simple. The instructions recommend drilling a hole in advance before screwing a screw into a concrete wall.

Before screwing a screw into concrete, you will need:. Tip: It should be borne in mind that there is no clear answer to the question of whether it is possible to drill concrete with a screwdriver. In this case, work should be carried out very carefully and only as a last resort. Self-tapping screws are used when installing plastic windows, any wooden structures, different profiles, door frames to a concrete or other base.

Before screwing a self-tapping screw into the concrete, a hole is drilled in the wall. Tip: To avoid breaking off the screw, you must screw it in correctly. This should be done carefully, without over-tightening the fasteners. You should avoid fast screwing in, which can lead to overheating of the element head and its destruction.

Characteristics

Using a concrete screw, you can greatly simplify the fastening of cabinets and other objects, and do it quickly and efficiently. The industry produces fasteners of all sizes and types. And to get more information on this topic, you should watch the video in this article. Concrete screw - types and methods of use Types of concrete screws.

The size of the screw is directly proportional to the load. For example, one screw measuring 3.0x12 mm weighs 0.4 g. A thousand pieces of this size will weigh 0.4 kg. One kilogram contains approximately hardware.

Regular straight cut of drywall

Before you start work, you need to prepare your workplace. Since the sheet is quite large, you will need plenty of space on the floor, and be sure to give yourself extra space to walk around the sheet, as stepping on drywall should only be done as a last resort. The floor surface must be dry and level, since during work you may need to step on the sheet, and the slightest unevenness on the floor will lead to damage or splitting. When cutting, quite a lot of dust is generated - in order not to contaminate the floor, it is recommended to use a special covering film.

Carefully place the sheet on the prepared floor surface.

IMPORTANT: Never throw a sheet of plasterboard on the floor - it can easily break. Using a tape measure and a simple pencil, make markings on a sheet of drywall, then, using a long ruler or rule, draw cutting lines

Using a tape measure and a simple pencil, mark the sheet of drywall, then use a long ruler or rule to draw cut lines.

Now, using a construction knife (it is advisable to use new blades for this operation), we cut the surface of the sheet along the drawn line. To make an even cut, do not use plastic or wooden tools, but only high-rigidity (metal) tools; to avoid injury, the tool must be of sufficient thickness. It is better to use a building level or rule.

There is no need to cut the sheet all the way through - this will ruin the floor; it is enough to cut the material a little less than halfway (the less you drag the knife along the line, the smoother the edge you will get). With sufficient skill, you will only need to make one cut. Lift the sheet and, holding the part to be cut with one hand, place a level or rule under the cut line (stepping back slightly towards the remaining part).

Release the sheet and break it at the cut site.

Then, turn the sheet over on its end and bend it along the cut line. Afterwards, carefully cut through the cardboard layer on the other side and separate the cut part.

Treat the cut edge with a special plane or a construction knife and sandpaper.

How to screw a dowel into concrete

• Before installing the structure, it is necessary to calculate the load. This is quite easy to do, since the diameter of the screws is standard. Lightweight items such as wall shelves can be mounted on 72mm long dowels. For heavy and bulky objects, the screw is selected individually.
• Before drilling, it is necessary to clean the wall surface. Future fastenings are marked on the surface. Before marking, you need to make sure that it does not fall into the passage of fittings or wiring. There should be no more than 60 centimeters between the fastening points; when installing windows, the step should be no more than 70 centimeters. 5-6 centimeters retreat from the edge of the wall.
• The depth of the drilled hole should be slightly greater than the length of the dowel. If the hole is not deep enough, a metal pin can be used to achieve the desired depth. During installation, deviations from the drilling axis are unacceptable; the drill must be held strictly perpendicular to the wall. The hole is cleaned of dust using a cleaning rod or a construction vacuum cleaner.
• In the absence of a tool, simply use a drill to drill a preliminary hole. He is driven into the wall with a hammer. After several blows, turn and hammer again until a hole of the required size is obtained.
• When screwing the dowel into concrete, it is not recommended to use a screwdriver. Since the screw itself is quite fragile, it may not withstand excessive tightening and the heat generated during operation of the power tool. For installation use a simple screwdriver. If you have problems with screwing, it is better to take a hammer. When screwing a screw into a wall made of porous concrete, the installation must be done carefully.

How to screw in a self-tapping screw when installing drywall

Before you screw a self-tapping screw into drywall, you need to think about tools that can make the job easier. Let's look at what tools and devices can be used: For a repairman, screwing in self-tapping screws is something understandable that does not raise any questions. Beginners believe that attaching drywall to the frame using self-tapping screws is the easiest to repair. But not everyone knows how to screw a self-tapping screw into drywall so that there are no problems later. Errors at this stage of repair can lead to the creation of a fragile coating.

The screws must be screwed in from one edge of the sheet to the other. You cannot screw them in at random, as this can lead to deformation of the drywall. The fastening pitch ranges from 15 to 30 cm, depending on the specific situation. The screwdriver applies slight pressure on the fastener and turns on maximum speed.

This is necessary so that the screw can fit into the profile to which the gypsum board is attached. As soon as it passes into the profile, you can reduce the speed and tighten the screw slowly. If the speed is not reduced, the sheet core will be damaged. The screw should fit into the sheet so that the head sank into it by 1-2 mm.

You need to work with a screwdriver gently, without much effort at first. If the self-tapping screw has not yet begun to enter the plasterboard, then the screwdriver under pressure may jump off and pierce the surface. When the screw has entered a little into the core of the material, you can already apply more force to screw it in completely.

Additional information on the topic:

• What is the difference between ceiling plasterboard and wall plasterboard
• Projects of plasterboard ceilings with suspended ceilings
• How to properly glue serpyanka to drywall when puttingtying
• What is needed for a plasterboard suspended ceiling
• Prices for puttying plasterboard ceilings for painting

Drilling drywall

Due to the great softness of drywall, almost any drills, drills and crowns can be used to drill sheets. However, preference should be given to drills (including feather drills) for wood, as well as crowns for wood and ceramics.

When drilling, it is advisable to place a wooden block or other not too hard material on the opposite side of the sheet, and, in the case of using a crown, you should drill approximately halfway on one side and finally on the opposite side, this way you can avoid chipping of the soft plaster on the back side of the sheet .

Types and sizes

Depending on the type of head, all self-tapping screws can be divided into several independent groups.

Varieties with a countersunk head. Such models most often have a conical design with cross-shaped slots. To work with this variety, you first need to prepare a seat. To do this, you need to make a small chamfer, which will allow you to place the end so that it is in the plane of the material. Models with this head structure will not protrude above the concrete surface after installation. Today varieties with a reduced head are produced. They have a smaller diameter and provide a more reliable fastening, but more effort must be applied when installing them.

Self-tapping screws can also be divided into separate categories depending on their protective coating. Many models are produced with a special oxidized coating. The latter has the appearance of a thin oxide film, which gives the parts a black color. Such options can withstand significant loads, but we must not forget that they should not come into contact with moisture during operation.

There are also models coated with phosphated compounds. These varieties, like the previous version, will be painted black. They are also capable of fixing material of significant weight, and at the same time have good resistance to water. The cost of such models will be higher compared to other types.

Galvanized concrete screws can be white or yellow, but they practically do not differ from each other in important properties. These models are most often used for installing products that will be located outdoors, since these self-tapping screws are particularly resistant to various atmospheric influences.

Self-tapping screws are also classified depending on the material from which they are made. The most common option is high-strength and high-quality carbon steel. This foundation is considered quite strong. Most often it is used together with impurities. In addition, this metal is particularly durable. Fastening devices made from this metal are relatively inexpensive.

Also, ordinary stainless steel can be used to produce such self-tapping screws. This material will be the best option if contact of fasteners with moisture is possible in the future. After all, models made from such material will not rust and will not lose their properties.

As a rule, self-tapping screws made of alloy stainless steel are not coated with additional protective coatings. After all, such metal contains nickel and chromium, which already provide excellent anti-corrosion properties of products.

There are also special types of decorative screws. They are most often made of wood, plastic or various non-ferrous metals. But such samples are extremely rarely taken for concrete surfaces, since they cannot withstand too heavy loads.

The sizes of self-tapping screws for concrete may vary. They are selected depending on the thickness of the surface and the diameter of the holes made.

Tools may have different thread configurations.

• "Herringbone". This type is a slightly inclined thread, which is formed by small metal cones nested inside each other. The herringbone model most often has a cross-section of 8 millimeters.
• Universal. This type of self-tapping screw can be used with or without a dowel. As a rule, the tool is available in sizes up to 6 millimeters.
• With a variable pitch of turns. These samples with variable pitch provide the most reliable fastening of materials, while additionally performing notches. It is this type that is most often found on self-tapping screws without drilling. The standard diameter of such devices is 7.5 millimeters.

The length of these devices can vary from 50 to 185 mm. The depth ranges from 2.3 to 2.8 mm. The height of the cap reaches 2.8-3.2 mm. The diameter of such screws can be from 6.3 to 6.7 mm

The thread pitch also plays an important role. For different models it can reach a value of 2.5-2.8 mm

Assortment and sizes

There are several types of designs of this material. They are divided into hexagonal and rectangular.

Hexagonal screws for concrete are a cone-shaped or cross-shaped slot. This type of screw is screwed using a spanner or open-end wrench. The rectangular appearance is characterized by a rounded head; this feature of the product allows you to hang suspended structures on self-tapping screws.

These types of fastenings are sold in all hardware stores. It is better not to take goods from the markets, because... Often sellers deceive buyers who do not understand products of this type.

Self-tapping screws also differ in the processing method, which can be of the following types:

The darkened type of screws is the most fragile, because... exposed to moisture. For this reason, it is not recommended to use this type of product in places with high humidity. Copper coated rivets are sensitive to temperature fluctuations. For this reason they are used indoors only. The most common model is galvanized self-tapping screws; this type can be used in any conditions.

To select fastening material for a concrete wall, a number of parameters should be taken into account. For example, the head height should fit within the range of 2.8 to 3.2 mm. The diameter of the cap should be 10.8-11.8 mm. Depth - from 2.3 to 2.8 mm. The length of the screw can be from 5 to 18.5 cm.

The size of the internal section is 5.1-5.5 mm, and the external section fits within the framework of 7.3-7.7 mm. The outer diameter is 6.3-6.6 mm.

General information

Although the modern construction market offers many options, self-tapping screws remain the most popular. They are screws of a rod-shaped, pointed shape, the head of which has a cross notch. Such a fastening element is characterized by high strength, which allows it not to bend or collapse under the influence of heavy loads.

How to use a concrete screw when working with foam concrete

Material

For the manufacture of self-tapping screws, various materials can be used, which are selected depending on the type and conditions of use.

The main ones are:

• carbon steel;
• stainless steel;
• brass.

The common feature of each of them is high strength, and their prices are not much different from each other.

The most common fasteners are made from carbon steel. Such self-tapping screws have an additional protective coating that protects them from oxidation and other types of influences.

Anchor screws for concrete

In order not to get confused about the types of coatings for carbon steel, you need to remember their color designation:

Before installing the self-tapping screw, make a hole for the dowel using a hammer drill

Concrete screw - types and methods of use

For example, one white screw measuring 2.5x10 mm weighs 0.3 g. A thousand pieces of this size would weigh 0.26 kg.

There are approximately pieces in one kilogram. For example, one screw measuring 75x mm weighs 36.2 grams. A thousand pieces of this size would weigh 36.2 kg.

The fastening of bricks to concrete depends on the thickness and strength of the surface. This takes into account the weight and location of the structure. Fastening brick to concrete is done using several methods. Attaching a brick to a concrete wall can be done in different ways, depending on the future structure. What to use for fastening so as not to damage the brickwork?

One kilogram contains approximately 28 pieces of hardware. Next, we will tell you which hole to drill and how to use dowels and tighten screws on concrete. In practice, the specified distance is used equal to mm. So, for a painting measuring 60 mm by 90 mm, you will need 4 screws; they will need to be installed in 4 corners.

If a cabinet measuring mm by mm is attached to the wall, then these are 8 screws. Of course, these are rough estimates.